Datacom-systems J Class Bedienungsanleitung Seite 117
- Seite / 273
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
6-6
Table 5–4. Problems Using a Hard Disk Drive
Problem Solution
The disk drive is not
accessible or does
not respond.
If problems persist, contact your system administrator or call
your designated service representative.
Make sure that all SCSI devices are
set to the proper SCSI ID. (See Ap-
pendix C for default SCSI ID set-
tings.)
Check that all SCSI devices are cor-
rectly cabled. Check that the SCSI bus
is correctly terminated. (See Appendix
C for information on SCSI cabling
and termination.)
Make sure that the system can com-
municate with the drive as described
in “Checking the SCSI IDs” in Ap-
pendix B.
Follow the instructions in “Dealing
With a Boot Failure” later in this
chapter.
- Owner’s Guide 1
- Hewlett-Packard Co. 1995 2
- Documentation 7
- Conventions 7
- Questions 8
- Suggestions, or 8
- Problems 8
- Contents 9
- Setting Up Your Printer 10
- Using Your CD–ROM Drive 10
- Chapter 2 10
- Chapter 3 10
- Using Your DDS Tape Drive 11
- Chapter 4 11
- SCSI Connections 13
- The Boot Console Interface 13
- Appendix C 13
- Appendix D 13
- Glossary 14
- Chapter 1 19
- • Internal Storage Devices 22
- • Keyboards PS/2 Keyboard 23
- Front Panel 24
- Controls, LED 24
- System LCD 25
- System Power Switch 25
- • CD-ROM disc drive 26
- • DDS tape drive 26
- • Floppy diskette drive 26
- Removable Device 27
- Bays (2) 27
- Audio Connectors 30
- • Audio Inputs Line-in 31
- • Audio Outputs Line-out 31
- • Audio CODEC Crystal CS4215 31
- Keyboard Connectors 32
- HP Parallel I/O Connector 33
- 802.3 Network Connectors 33
- SCSI Connectors 34
- Power Cord Connector 34
- Monitors 35
- • PS/2 Keyboard 36
- • ITF Keyboard 36
- Keyboards 36
- Pointing Devices 39
- Operating 40
- Overview 40
- LANIC ID 41
- Terminal Control 42
- Networking 45
- Toolbox 50
- Up Arrow 50
- 13. Click on 52
- Exit SAM 54
- Printing a File 58
- Chapter 6 60
- Media Descrip 62
- CD-ROM Media 64
- Figure 6–4 67
- Figure 6–4. Disc Tray Closed 67
- The ioscan utility verifies 70
- Mounting and 74
- Unmounting a 74
- CD-ROM Disc 74
- Reading the Busy Light 80
- Troubleshooting 81
- Descriptions 84
- LEDs (light emitting 85
- Data Cassettes 88
- H/W Path Description Status 91
- Writing to a Data Cassette 95
- Further Command Information 98
- Ordering Information 99
- Chapter 5 100
- Using the Floppy 102
- Diskette 102
- Eject Button 103
- Operating the 104
- Floppy Drive 104
- Using Device Files 106
- Formatting a New Diskette 107
- For More Information 110
- • Using HP-UX (B2910–90001) 111
- Problems and 114
- Solutions 114
- The search command 121
- Failures 122
- Running System 126
- Verification 126
- 5. Press 127
- CSTM> exit 128
- Appendix A 129
- • Number 1 Posi-drive driver 130
- • Needlenose pliers 130
- Checking the 131
- SCSI IDs 131
- /usr/sbin/ioscan –f 132
- Opening the 134
- System Unit 134
- Closing the 136
- CD-ROM Drive 142
- 143
- DDS Tape Drive 144
- SCSI Terminators 145
- (must be removed) 145
- Top View of Floppy Disk Drive 150
- 14. Slide the drawer back in 152
- Adding a 155
- Hard Drive 155
- 156
- PCB Side of Drive 157
- Top Drive 157
- Bottom Drive 157
- Installing a Hard Disk Drive 158
- Configuring a Hard Drive 161
- 11. Click on 163
- Ejector Tab 165
- Memory SIMMs 166
- 167
- 167
- 11. Close the ejector tab 169
- Figure A–37 185
- Changing Your 188
- Monitor Type 188
- Appendix B 189
- VCCI Class 1 ITE 192
- Kingdom Only) 192
- CLASS 1 LASER PRODUCT 193
- LASER KLASSE 1 193
- Warnings and 194
- Cautions 194
- SCSI Bus 197
- Differences 197
- Priority 198
- SCSI–2 ID Number 198
- • fast-wide, SCSI-3 bus 201
- Determining 203
- Fast, Wide SCSI-3 Bus Length 206
- Assigning SCSI 208
- Device IDs 208
- Fast, Wide SCSI IDs 214
- Connecting to 215
- 216
- Boot terminated 225
- Booting Your 226
- Workstation 226
- ISL> hpux /SYSBCKUP 227
- Searching for 228
- Bootable Media 228
- Resetting Your 229
- Displaying and 229
- Setting Paths 229
- Setting the 231
- • Graphics slot 1 CRX48Z 232
- • Graphics slot 2 Empty 232
- Setting the Monitor Type 233
- Displaying the 236
- Configuration 236
- Sample Output 2 237
- Status of the 239
- EISA Slots 239
- Auto Boot and 240
- Auto Search 240
- Displaying 242
- Information 242
- Displaying PIM 242
- Workspace Manager 266
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.035 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern